YG-1 G1 Series Vanadium Alloy HSS Spiral Flute Tap, TiN Coated, Round Shank with Square End, Modified Bottoming Chamfer, 4-40 Thread Size, H2 Tolerance
- When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging. 03125-inches thread length. Titanium nitride coatings add a hard layer of gold-colored ceramic to the surface that extends tool life and permits faster cutting speeds than uncoated tools. Round shanks allow use with a wide variety of toolholding systems. High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance.
Walton 18003 6-Piece 4 Flute Tap Extractor Set With Square Shank
- Tapered square shank fits into manual brace tools and drivers handles for added cutting pressure. 5 piece set contains sizes 5/16″, 3/8″, 7/16″, 1/2″, 5/8″. For removing machine screws and broken hand taps. Hardened steel fingers of walton tap extractors fit in the flutes of a broken tap to back it out simply and safely. Packed in 6-compartment plastic case.
YG-1 F8 Series Vanadium Alloy HSS Spiral Flute Tap, TiN Coated, Round Shank with Square End, Bottoming Chamfer, 6-32 Thread Size, H3 Tolerance
- Round shanks allow use with a wide variety of toolholding systems. Titanium nitride coatings add a hard layer of gold-colored ceramic to the surface that extends tool life and permits faster cutting speeds than uncoated tools. When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging. 0375-inches thread length. High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance.
YG-1 F4 Series Vanadium Alloy HSS Spiral Flute Tap, Steam Oxide, Round Shank with Square End, Bottoming Chamfer, 3/8″-16 Thread Size, H3 Tolerance
- Black oxide treatment adds lubricity and creates small pockets on the surface of the tool that act to hold coolant near the cutting edge. 075-inches thread length. High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance. When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging. Round shanks allow use with a wide variety of toolholding systems.
Walton 10754 3/4″, 4 Flute Tap Extractor With Square Shank
- For removing machine screws and broken hand taps. When fingers become bent or broken or are too short for further use, replacement fingers are available. Hardened steel fingers of walton tap extractors fit in the flutes of a broken tap to back it out simply and safely. Threads per inch need not be specified as tap extractors will fit both nc and nf taps. Tapered square shank fits into manual brace tools and drivers handles for added cutting pressure.
YXQ M3 x 0.5mm Tap Machine HSS Metric Right Hand Thread 3 Straight Flute Taps Taper and Plug, 4Pcs
- 3 straight threaded flutethread directionright hand. Item namemetric tap,plug typematerial hss(high speed steel). Flute diameter 3mm / 01″flute teeth pitch 05mm / 002″. Package include 4 x taper andmetric tap. Total length 42mm / 166″ shank dia 3mm / 01″.
MaxTool 3/4-10 Spiral Flute Tap; 10TPI HSS M2 Fully Ground Right Hand; SFF02W02R48
- It is available in three different ansi standards unc (unified coarse), unf (unified fine), or uns (unified special). This uncoated taps can be used on a broad range of materials. The round shank with square driver makes the taps suitable for hand or power-driven applications. Maxtool is a cutting tools distributor in new york to meet a wide range cutting demand of customers in today’s markets, which include automotive, aerospace, electronics, medical, printed circuit boards, optical industries, and moremaxtool maintains the leading spirit in supply of standard and custom-made high performance cutting tools, such as polycrystalline diamond (pcd), polycrystalline cubic boron nitride (pcbn), carbide, high speed steel (hss) tools, hole saws, diamond wheels, etc for machining ferrous, non-ferrous, composite, fiberglass, and carbon fiber materials. Maxtool unc and unf uncoated high-speed steel spiral flute taps have spiral flutes and round shanks with square driver. You can always rely on maxtoolmaxtool’s slogan is consistent quality maxtool toolmax. They are used to create right-hand threads in a range of materials. The spiral flutes are suitable for threading through holes and blind or bottoming holes. We offer our products worldwide, unless otherwise restricted by our suppliersin addition, maxtool offers re-sharpening services and custom tooling solutionsmaxtool warmly welcomes everyone to visit our amazon store, and honestly appreciates everyone very much to give a cooperative chance to discuss your requirementmaxtool will do the best to make each buyer satisfaction. The premium high speed steel material provides long tool life.
YG-1 G4 Series Vanadium Alloy HSS Spiral Flute Tap, Uncoated (Bright) Finish, Round Shank with Square End, Bottoming Chamfer, M6-1 Thread Size, D5 Tolerance
- Uncoated tools feature just the base substrate without any additional treatment or coatings and are suitable for a wide range of applications. High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance. When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging. 0625-inches thread length. Round shanks allow use with a wide variety of toolholding systems.
Walton 18013 13 Piece Multi Flute Tap Extractor Set With Square Shank
- Tapered square shank fits into manual brace tools and drivers handles for added cutting pressure. Hardened steel fingers of walton tap extractors fit in the flutes of a broken tap to back it out simply and safely. 13 piece set contains sizes #4 (3-flute), #5 (3-flute), #6 (3-flute), #8, #10, #12, 1/4″, 5/16″, 3/8″, 7/16″, 1/2″, 5/8″, 3/4″. Packed in 15-compartment plastic case. For removing machine screws and broken hand taps.
Walton 18015-3 15 Piece 3 Flute Tap Extractor Set With Square Shank
- Tapered square shank fits into manual brace tools and drivers handles for added cutting pressure. For removing machine screws and broken hand taps. Hardened steel fingers of walton tap extractors fit in the flutes of a broken tap to back it out simply and safely. Packed in 15-compartment plastic case. 15 piece set contains sizes #4, #5, #6, #8, #10, #12, 1/4″, 5/16″, 3/8″, 7/16″, 1/2″, 5/8″, 3/4″, 7/8″, 1″.
YG-1 F4 Series Vanadium Alloy HSS Spiral Flute Tap, Steam Oxide, Round Shank with Square End, Bottoming Chamfer, 1/4″-20 Thread Size, H3 Tolerance
- Black oxide treatment adds lubricity and creates small pockets on the surface of the tool that act to hold coolant near the cutting edge. When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging. 0625-inches thread length. Round shanks allow use with a wide variety of toolholding systems. High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance.
Walton 10063 #6, 3 Flute Tap Extractor With Square Shank
- Threads per inch need not be specified as tap extractors will fit both nc and nf taps. For removing machine screws and broken hand taps. When fingers become bent or broken or are too short for further use, replacement fingers are available. Tapered square shank fits into manual brace tools and drivers handles for added cutting pressure. Hardened steel fingers of walton tap extractors fit in the flutes of a broken tap to back it out simply and safely.
Walton 10252 1/4″, 2 Flute Tap Extractor With Square Shank
- Threads per inch need not be specified as tap extractors will fit both nc and nf taps. For removing machine screws and broken hand taps. Hardened steel fingers of walton tap extractors fit in the flutes of a broken tap to back it out simply and safely. When fingers become bent or broken or are too short for further use, replacement fingers are available. Tapered square shank fits into manual brace tools and drivers handles for added cutting pressure.
Spiral Flute Tap, Bottom, HSS, TiN, 10-24
- 5p-2p, pitch diameter limits 2b, standard projection, shank diameter 0. Spiral flute tap, bottoming, style general purpose, high speed steel, finish tin, number of flutes 3, size #10, pitch 24, thread unc, chamfer 1. General purpose hss spiral flute taps for blind holes in general machining applications. 194″, for tapping internal threads in aluminum, mild steels and medium carbon steels, tolerance 2b, ansi standards 298.
MaxTool 1/2-13 Spiral Flute Tap; 13TPI HSS M2 Fully Ground Right Hand; SFF02W02R32
- We offer our products worldwide, unless otherwise restricted by our suppliersin addition, maxtool offers re-sharpening services and custom tooling solutionsmaxtool warmly welcomes everyone to visit our amazon store, and honestly appreciates everyone very much to give a cooperative chance to discuss your requirementmaxtool will do the best to make each buyer satisfaction. This uncoated taps can be used on a broad range of materials. You can always rely on maxtoolmaxtool’s slogan is consistent quality maxtool toolmax. They are used to create right-hand threads in a range of materials. Maxtool unc and unf uncoated high-speed steel spiral flute taps have spiral flutes and round shanks with square driver. The round shank with square driver makes the taps suitable for hand or power-driven applications. Maxtool is a cutting tools distributor in new york to meet a wide range cutting demand of customers in today’s markets, which include automotive, aerospace, electronics, medical, printed circuit boards, optical industries, and moremaxtool maintains the leading spirit in supply of standard and custom-made high performance cutting tools, such as polycrystalline diamond (pcd), polycrystalline cubic boron nitride (pcbn), carbide, high speed steel (hss) tools, hole saws, diamond wheels, etc for machining ferrous, non-ferrous, composite, fiberglass, and carbon fiber materials. The premium high speed steel material provides long tool life. It is available in three different ansi standards unc (unified coarse), unf (unified fine), or uns (unified special). The spiral flutes are suitable for threading through holes and blind or bottoming holes.
YG-1 G4 Series Vanadium Alloy HSS Spiral Flute Tap, Uncoated (Bright) Finish, Round Shank with Square End, Bottoming Chamfer, M5-0.8 Thread Size, D4 Tolerance
- Uncoated tools feature just the base substrate without any additional treatment or coatings and are suitable for a wide range of applications. 05-inches thread length. Round shanks allow use with a wide variety of toolholding systems. High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance. When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging.
Walton 10084 #8, 4 Flute Tap Extractor With Square Shank
- For removing machine screws and broken hand taps. Hardened steel fingers of walton tap extractors fit in the flutes of a broken tap to back it out simply and safely. When fingers become bent or broken or are too short for further use, replacement fingers are available. Tapered square shank fits into manual brace tools and drivers handles for added cutting pressure. Threads per inch need not be specified as tap extractors will fit both nc and nf taps.
YG-1 F4 Series Vanadium Alloy HSS Spiral Flute Tap, Steam Oxide, Round Shank with Square End, Bottoming Chamfer, 5/8″-11 Thread Size, H3 Tolerance
- Black oxide treatment adds lubricity and creates small pockets on the surface of the tool that act to hold coolant near the cutting edge. High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance. 109375-inches thread length. Round shanks allow use with a wide variety of toolholding systems. When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging.
Walton 10043 #4, 3 Flute Tap Extractor With Square Shank
- When fingers become bent or broken or are too short for further use, replacement fingers are available. For removing machine screws and broken hand taps. Hardened steel fingers of walton tap extractors fit in the flutes of a broken tap to back it out simply and safely. Tapered square shank fits into manual brace tools and drivers handles for added cutting pressure. Threads per inch need not be specified as tap extractors will fit both nc and nf taps.
We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.
