Nylon 6/6 Pan Head Machine Screw, Black, #2 Phillips Drive, #8-32 Thread Size, 1″ Length, Fully Threaded, USA Made (Pack of 100)
- Hex washer head has a flange for additional grip with the mating surface. Zinc plating resists corrosion and has a reflective appearance. Slotted drive has a linear slot for use with a flat-blade driver. Thread cutting screw with type f point has machine screw threads that taper down to a blunt edge and is suitable for heavy gauge sheet metal, aluminum, cast iron, brass, and plastic. Steel is often used in applications where strength is the primary consideration.
Steel Tapped-Hole U-Style Clip-On Nut, Plain Finish, #8-32 Thread Size, For 0.079″-0.118″ Material Thickness, 0.375″ Edge Distance (Pack of 25)
- Designed to clip onto panels for quick alignment and fasten with a machine screw for a secure hold. Steel is often used in applications where strength is the primary consideration. Hole is tapped, or fully threaded, for screws that need to extend beyond the bottom of the nut. Clip is u-shaped for a secure hold on both sides of the panel when screwing down. Plain surface has no.
Nylon 6/6 Small Pattern Machine Screw Hex Nut, Off-White, #8-32 Thread Size, 11/32″ Width Across Flats, 9/64″ Thick (Pack of 100)
- Ensure a lasting hold for any project. Coarse threads are better for brittle materials, and will assemble and disassemble more quickly than fine threads. Nylon 6/6 is suitable where non-conductivity, corrosion resistance, and cost are important considerations. Hex nuts are appropriate for use in low-strength assemblies. Drive system is a hexagon-shaped head.
Steel Pan Head Machine Screw, Yellow Zinc Plated, Meets ASME B18.6.3, #2 Phillips Drive, #8-32 Thread Size, 1-3/4″ Length, Fully Threaded, Import (Pack of 50)
- Right-hand cut tools have a cutting action that engages when they are run in a clockwise direction. Round shanks allow use with a wide variety of toolholding systems. High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance. Straight flute tools allow chips to collect in the flutes as they cut and are well suited for most applications in shallow cuts. Black oxide treatment adds lubricity and creates small pockets on the surface of the tool that act to hold coolant near the cutting edge.
Nylon 6/6 Pan Head Machine Screw, Off-White, #2 Phillips Drive, #8-32 Thread Size, 1/4″ Length, Fully Threaded, USA Made (Pack of 100)
- Clip is u-shaped for a secure hold on both sides of the panel when screwing down. Steel is often used in applications where strength is the primary consideration. Designed to clip onto panels for quick alignment and a secure hold. Plain surface has no.
Steel Pan Head Machine Screw With Internal-Tooth Lock Washer, Black Oxide Finish, Meets ASME B18.13, #2 Phillips Drive, #8-32 Thread Size, 3/8″ Length, Fully Threaded, Import (Pack of 100)
- High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance. Round shanks allow use with a wide variety of toolholding systems. Titanium nitride coatings add a hard layer of gold-colored ceramic to the surface that extends tool life and permits faster cutting speeds than uncoated tools. When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging. 0375-inches thread length.
Steel Pan Head Machine Screw, Zinc Plated, Meets ASME B18.6.3, T20 Star Drive, #8-32 Thread Size, 1/4″ Length, Fully Threaded, Imported (Pack of 100)
- High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance. Round shanks allow use with a wide variety of toolholding systems. When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging. Titanium nitride coatings add a hard layer of gold-colored ceramic to the surface that extends tool life and permits faster cutting speeds than uncoated tools. 0375-inches thread length.
Steel Pan Head Machine Screw, Zinc Plated, Meets ASME B18.6.3, #2 Phillips Drive, #8-32 Thread Size, 4″ Length, Fully Threaded, Imported (Pack of 10)
- When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging. Round shanks allow use with a wide variety of toolholding systems. Uncoated tools feature just the base substrate without any additional treatment or coatings and are suitable for a wide range of applications. 0276-inches thread length. High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance.
Steel Pan Head Machine Screw, Zinc Plated, Meets ASME B18.6.3, #2 Phillips Drive, #8-32 Thread Size, 2-1/4″ Length, Fully Threaded, Imported (Pack of 25)
- Steel is often used in applications where strength is the primary consideration. Hex washer head has a flange for additional grip with the mating surface. Slotted drive has a linear slot for use with a flat-blade driver. Zinc plating resists corrosion and has a reflective appearance. Thread cutting screw with type f point has machine screw threads that taper down to a blunt edge and is suitable for heavy gauge sheet metal, aluminum, cast iron, brass, and plastic.
Steel Pan Head Machine Screw, Black Oxide Finish, Meets ASME B18.6.3, #2 Phillips Drive, #8-32 Thread Size, 1-3/4″ Length, Fully Threaded, Import (Pack of 100)
- Coarse threads are better for brittle materials, and will assemble and disassemble more quickly than fine threads. Hex nuts are appropriate for use in low-strength assemblies. Nylon 6/6 is suitable where non-conductivity, corrosion resistance, and cost are important considerations. Drive system is a hexagon-shaped head. Ensure a lasting hold for any project.
Steel Pan Head Machine Screw, Black Oxide Finish, Meets ASME B18.6.3, #2 Phillips Drive, #8-32 Thread Size, 1-1/4″ Length, Fully Threaded, Import (Pack of 100)
- High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance. 0276-inches thread length. Round shanks allow use with a wide variety of toolholding systems. Uncoated tools feature just the base substrate without any additional treatment or coatings and are suitable for a wide range of applications. When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging.
18-8 Stainless Steel Pan Head Machine Screw, Black Oxide Finish, Meets ASME B18.6.3, T20 Star Drive, #8-32 Thread Size, 3/4″ Length, Fully Threaded, Imported (Pack of 50)
- Thread cutting screw with type f point has machine screw threads that taper down to a blunt edge and is suitable for heavy gauge sheet metal, aluminum, cast iron, brass, and plastic. Flat undercut head has a flat top with an 82-degree cone-shaped bearing surface and is undercut for use in shallow countersunk holes. Plain surface has no finish or coating. Phillips drive has an x-shaped slot that accepts a phillips driver and is designed to prevent over-tightening. 18-8 stainless steel provides good corrosion resistance and strength.
18-8 Stainless Steel Thread Cutting Screw, Plain Finish, Hex Washer Head, Slotted Drive, Type F, #8-32 Thread Size, 1/4″ Length (Pack of 25)
- Slotted drive has a linear slot for use with a flat-blade driver. Plain surface has no finish or coating. Thread cutting screw with type f point has machine screw threads that taper down to a blunt edge and is suitable for heavy gauge sheet metal, aluminum, cast iron, brass, and plastic. 18-8 stainless steel provides good corrosion resistance and strength. Hex washer head has a flange for additional grip with the mating surface.
Steel Pan Head Machine Screw, Zinc Plated, Meets ASME B18.6.3, #2 Phillips Drive, #8-32 Thread Size, 5″ Length, Fully Threaded, Imported (Pack of 10)
- . They are available with a variety of head shapes, which determine how the screw interacts with the mating surface, and drive styles, which determine the type of driver required to install and remove the screw. Machine screws are threaded fasteners that are typically used with nuts or drilled and tapped (threaded) holes.
Steel Pan Head Machine Screw, Black Oxide Finish, Meets ASME B18.6.3, #2 Phillips Drive, #8-32 Thread Size, 3/4″ Length, Fully Threaded, Import (Pack of 100)
- They are available with a variety of head shapes, which determine how the screw interacts with the mating surface, and drive styles, which determine the type of driver required to install and remove the screw. . Machine screws are threaded fasteners that are typically used with nuts or drilled and tapped (threaded) holes.
Steel Pan Head Machine Screw, Zinc Plated, Meets ASME B18.6.3, #2 Phillips Drive, #8-32 Thread Size, 3-1/2″ Length, Fully Threaded, Imported (Pack of 10)
- Titanium nitride coatings add a hard layer of gold-colored ceramic to the surface that extends tool life and permits faster cutting speeds than uncoated tools. Round shanks allow use with a wide variety of toolholding systems. When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging. 0375-inches thread length. High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance.
Black Oxide Alloy Steel Hex Socket Head Cap Screw, Self Locking, #8-32 Thread Size, 1″ Length, Fully Threaded (Pack of 25)
- Thread cutting screw with type f point has machine screw threads that taper down to a blunt edge and is suitable for heavy gauge sheet metal, aluminum, cast iron, brass, and plastic. Flat undercut head has a flat top with an 82-degree cone-shaped bearing surface and is undercut for use in shallow countersunk holes. 18-8 stainless steel provides good corrosion resistance and strength. Plain surface has no finish or coating. Phillips drive has an x-shaped slot that accepts a phillips driver and is designed to prevent over-tightening.
Polycarbonate Pan Head Machine Screw, Slotted Drive, #8-32 Thread Size, 3/4″ Length, Fully Threaded, USA Made (Pack of 25)
- 18-8 stainless steel provides good corrosion resistance and strength. Thread cutting screw with type f point has machine screw threads that taper down to a blunt edge and is suitable for heavy gauge sheet metal, aluminum, cast iron, brass, and plastic. Phillips drive has an x-shaped slot that accepts a phillips driver and is designed to prevent over-tightening. Plain surface has no finish or coating. Flat undercut head has a flat top with an 82-degree cone-shaped bearing surface and is undercut for use in shallow countersunk holes.
Steel Pan Head Machine Screw, Zinc Plated, Meets ASME B18.6.3, #2 Phillips Drive, #8-32 Thread Size, 4-1/2″ Length, Fully Threaded, Imported (Pack of 10)
- Hex washer head has a flange for additional grip with the mating surface. Slotted drive has a linear slot for use with a flat-blade driver. Plain surface has no finish or coating. Thread cutting screw with type f point has machine screw threads that taper down to a blunt edge and is suitable for heavy gauge sheet metal, aluminum, cast iron, brass, and plastic. 18-8 stainless steel provides good corrosion resistance and strength.
Steel Thread Cutting Screw, Zinc Plated Finish, Hex Washer Head, Slotted Drive, Type F, #8-32 Thread Size, 3/8″ Length (Pack of 100)
- Zinc plating resists corrosion and has a reflective appearance. Hex washer head has a flange for additional grip with the mating surface. Steel is often used in applications where strength is the primary consideration. Slotted drive has a linear slot for use with a flat-blade driver. Thread cutting screw with type f point has machine screw threads that taper down to a blunt edge and is suitable for heavy gauge sheet metal, aluminum, cast iron, brass, and plastic.
Steel Standard U-Style Clip-On Nut, Plain Finish, #8-32 Thread Size, For 0.025″-0.04″ Material Thickness, 0.515″ Edge Distance (Pack of 25)
- Plain surface has no. Steel is often used in applications where strength is the primary consideration. Designed to clip onto panels for quick alignment and a secure hold. Clip is u-shaped for a secure hold on both sides of the panel when screwing down.
Nylon 6/6 Pan Head Machine Screw, Off-White, #2 Phillips Drive, #8-32 Thread Size, 2″ Length, Fully Threaded, USA Made (Pack of 100)
- 18-8 stainless steel provides good corrosion resistance and strength. Phillips drive has an x-shaped slot that accepts a phillips driver and is designed to prevent over-tightening. Flat undercut head has a flat top with an 82-degree cone-shaped bearing surface and is undercut for use in shallow countersunk holes. Plain surface has no finish or coating. Thread cutting screw with type f point has machine screw threads that taper down to a blunt edge and is suitable for heavy gauge sheet metal, aluminum, cast iron, brass, and plastic.
We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.
