15 Coolest Square Noses

 

Niagara Cutter N90284 High Speed Steel Square Nose End Mill Weldon Shank Uncoated Bright Finish Finishing Cutting 37-Degree 2-Flute 4125 OAL 0875 Cut Diameter 075 Shank Diameter

Niagara Cutter N90284 High Speed Steel Square Nose End Mill, Weldon Shank, Uncoated (Bright) Finish, Finishing Cutting, 37-Degree, 2-Flute, 4.125″ OAL, 0.875″ Cut Diameter, 0.75″ Shank Diameter

Niagara Cutter N90284 High Speed Steel Square Nose End Mill, Weldon Shank, Uncoated (Bright) Finish, Finishing Cutting, 37-Degree, 2-Flute, 4.125″ OAL, 0.875″ Cut Diameter, 0.75″ Shank Diameter - High-speed steel is a common general-purpose steel for cutting tools. 37-degree helix angle provides efficient cutting action and chip evacuation required to machine aluminum and other nonferrous materials. Two flutes offer better chip-carrying capacity than end mills with more flutes. Square end creates sharp, unrounded cuts. Center-cutting design allows the end mill to plunge into material like a drill bit while also performing conventional surface milling.

 

CGC Tools CEM18F3TICN Primate Square Nose End Mill TiCN Coating 3 Flute 18 Diameter 12 LOC 1-12 OAL

CGC Tools CEM18F3TICN Primate Square Nose End Mill, TiCN Coating, 3 Flute, 1/8″ Diameter, 1/2″ LOC, 1-1/2″ OAL

CGC Tools CEM18F3TICN Primate Square Nose End Mill, TiCN Coating, 3 Flute, 1/8″ Diameter, 1/2″ LOC, 1-1/2″ OAL - Highest transverse rupture strength (trs) nano-grain carbide substrate available and completely resharpenable. Gmp edge prepped to hone the “ridges” to reduce fracturing during the milling process while greatly increasing tool life and enhancing finish. Extremely versatile in various materials, center cutting, solid sub-micron carbide. This weapon of mass production destroy any competition. Usa, flat, 3 flute, 1/8” diameter, 1/2” length of cut, 1-1/2” overall length, ticn coating.

 

EnPointâ„¢ High Hardness Aluminum Cutting 2 Flutes Carbide End Mill 18 3175mm Shank 1mm Cutter Dia Metalworking Square Nose CNC Spiral Milling Cutter for Brass Copper Foil IC Substrate

EnPointâ„¢ High Hardness Aluminum Cutting 2 Flutes Carbide End Mill 1/8″ 3.175mm Shank 1mm Cutter Dia Metalworking Square Nose CNC Spiral Milling Cutter for Brass Copper Foil IC Substrate

EnPointâ„¢ High Hardness Aluminum Cutting 2 Flutes Carbide End Mill 1/8″ 3.175mm Shank 1mm Cutter Dia Metalworking Square Nose CNC Spiral Milling Cutter for Brass Copper Foil IC Substrate - Less heat build up 2 flutes also allow for faster feed and speed rates. Sharp cutting edge produces an excellent surface finish and great work efficiency. Mainly for cutting aluminum substrate, full copper foil and other high ductility metal plates and it can also be used for pbga/boc/csp and intergrated circuit substrate molding. Produced from a premium ultra fine solid carbide for maximum tool strength and durability. 2 flutes with large spiral chip groove bring better chip evacuation, preventing from sticking chips.

 

Prefinished Maple Wood Floor Flooring Square NoseCarpet Reducer or End Cap For 916 Floating Wood Floor Molding Trim

Prefinished Maple Wood Floor Flooring Square Nose,Carpet Reducer or End Cap For 9/16″ Floating Wood Floor Molding Trim

Prefinished Maple Wood Floor Flooring Square Nose,Carpet Reducer or End Cap For 9/16″ Floating Wood Floor Molding Trim - Prefinished maple square nose ( end cap, carpet reducer ). Solid maple hardwood uses for floor height between 9/16″ to 5/8″. Please note this molding is special order order cannot be cancelled once your order being processed. Length 78″ (65 feet). Aluminium oxide finish, lifetime warranty.

 

Melin Tool AMG-E Carbide Square Nose End Mill AlTiN Monolayer Finish 30 Deg Helix 2 Flutes 4 Overall Length 02500 Cutting Diameter 025 Shank Diameter

Melin Tool AMG-E Carbide Square Nose End Mill, AlTiN Monolayer Finish, 30 Deg Helix, 2 Flutes, 4″ Overall Length, 0.2500″ Cutting Diameter, 0.25″ Shank Diameter

Melin Tool AMG-E Carbide Square Nose End Mill, AlTiN Monolayer Finish, 30 Deg Helix, 2 Flutes, 4″ Overall Length, 0.2500″ Cutting Diameter, 0.25″ Shank Diameter - Square nose end mills (also called square end) create sharp, unrounded cuts. Carbide can run at higher speeds than high-speed or cobalt steel, resisting wear and high cutting temperatures. Extra-long-length end mills have longer cutting edges and can make deeper cuts than long-length end mills. Suitable for general-purpose machining on most medium-hardness materials, including steel and iron. Aluminum titanium nitride (altin) coating lubricates the end mill for high-temperature stability and abrasion resistance at high cutting speeds, offering better heat resistance than tin, tialn, and ticn coatings.

 

Moldings Online 78 x 15625 x 088 Armstrong Oceanside Gray Prime Harvest Red Oak Square Nose 78 L

Moldings Online 78″ x 1.5625″ x 0.88″ Armstrong Oceanside Gray Prime Harvest Red Oak Square Nose, 78″ L

Moldings Online 78″ x 1.5625″ x 0.88″ Armstrong Oceanside Gray Prime Harvest Red Oak Square Nose, 78″ L - . Square nosing is ideal for concealing expansion spaces along a vertical object that cannot be framed, such as sliding glass door or brick fireplace.

 

Melin Tool EMG-M-M Carbide Micro Square Nose End Mill Metric Uncoated Bright Finish 30 Deg Helix 3 Flutes 38mm Overall Length 1mm Cutting Diameter 3mm Shank Diameter

Melin Tool EMG-M-M Carbide Micro Square Nose End Mill, Metric, Uncoated (Bright) Finish, 30 Deg Helix, 3 Flutes, 38mm Overall Length, 1mm Cutting Diameter, 3mm Shank Diameter

Melin Tool EMG-M-M Carbide Micro Square Nose End Mill, Metric, Uncoated (Bright) Finish, 30 Deg Helix, 3 Flutes, 38mm Overall Length, 1mm Cutting Diameter, 3mm Shank Diameter - Uncoated tools feature just the base substrate without any additional treatment or coatings and are suitable for a wide range of applications. 30 degree helix angle. Round shanks allow use with a wide variety of toolholding systems. General purpose square end. Solid carbide tools offer long tool life and faster cutting speeds than other substrates, but are more brittle and must be used with rigid toolholding systems.

 

Enpointâ„¢ TiAlN Coated Stainless Cutting Ultra-fine Submicron Carbide 2-Flute Square Nose End Mill 532 4mm Shank 4mm Cut Width CNC Metalworking Milling Cutter for Aluminum Iron Brass

Enpointâ„¢ TiAlN Coated Stainless Cutting Ultra-fine Submicron Carbide 2-Flute Square Nose End Mill 5/32″ 4mm Shank 4mm Cut Width CNC Metalworking Milling Cutter for Aluminum Iron Brass

Enpointâ„¢ TiAlN Coated Stainless Cutting Ultra-fine Submicron Carbide 2-Flute Square Nose End Mill 5/32″ 4mm Shank 4mm Cut Width CNC Metalworking Milling Cutter for Aluminum Iron Brass - Produced from a premium, ultra-fine solid carbide for maximum tool strength and durability. Mainly suitable for milling materials from soft plastics to tough aerospace alloys including aluminum, stainless steel, mold and alloy steels, inconel, hastelloy and titanium. Center cutting for straight plunging or ramping down into the workpiece. Coated with ti-al-x-n can cut hard materials and keeps longer tool life sharp cutting edge produces an excellent surface finish. 2 flutes allow for higher feedrates and large chip clearance to prevent chips sticking in the flutes.

 

CGC Tools GMA14F2 Gorilla Silverback Carbide Square Nose End Mill for Aluminum Flat End 2 Flute 14 Diameter 34 LOC 3 OAL

CGC Tools GMA14F2 Gorilla Silverback Carbide Square Nose End Mill for Aluminum, Flat End, 2 Flute, 1/4″ Diameter, 3/4″ LOC, 3″ OAL

CGC Tools GMA14F2 Gorilla Silverback Carbide Square Nose End Mill for Aluminum, Flat End, 2 Flute, 1/4″ Diameter, 3/4″ LOC, 3″ OAL - Engineered to repel aluminum for roughing and finishing of non-ferrous materials, high velocity, high material removal rate. Highest transverse rupture strength (trs) nano-grain carbide substrate available and completely resharpenable. Usa, silverback, flat, 2 flute, 1/4″ diameter, 3/4″ length of cut, 3″ overall length. Gmp edge prepped to hone the “ridges” to reduce fracturing during the milling process while greatly increasing tool life and enhancing finish.

 

Extra Heavy-Duty Scraper 12 Square Nose

Extra Heavy-Duty Scraper, 1/2″ Square Nose

Extra Heavy-Duty Scraper, 1/2″ Square Nose - Designed to make tight radius turns or to be used in narrow turnings, this scraper is sized to work in most turning situations. It features a 7″ long blade and 14″ ash handle. This woodcraft exclusive 1/2” square nose, extra heavy-duty scraper is a full 1/2″ thick to help eliminate chatter. .

 

Niagara Cutter N61647 Carbide Square Nose End Mill Inch TiCN Finish Roughing and Finishing Cut 45 Degree Helix 3 Flutes 4 Overall Length 0375 Cutting Diameter 0375 Shank Diameter

Niagara Cutter N61647 Carbide Square Nose End Mill, Inch, TiCN Finish, Roughing and Finishing Cut, 45 Degree Helix, 3 Flutes, 4″ Overall Length, 0.375″ Cutting Diameter, 0.375″ Shank Diameter

Niagara Cutter N61647 Carbide Square Nose End Mill, Inch, TiCN Finish, Roughing and Finishing Cut, 45 Degree Helix, 3 Flutes, 4″ Overall Length, 0.375″ Cutting Diameter, 0.375″ Shank Diameter - Carbide can run at higher speeds than high-speed or cobalt steel, resisting wear and high cutting temperatures. Square nose end mills (also called square end) create sharp, unrounded cuts. Three flutes provide better chip-carrying capacity than four flutes and a finer finish than two, reducing the need for a second finishing cut in some applications. Titanium carbon nitride (ticn) coating lubricates the end mill for high-temperature stability and offers the abrasion resistance required to machine aluminum and other nonferrous materials. 45-degree helix provides the efficient cutting action and chip evacuation required to machine aluminum and other nonferrous materials.

 

Niagara Cutter N35160 High Speed Steel Square Nose End Mill Weldon Shank TiN Finish RoughingFinishing Cut Non-Center 30-Degree 4-Flute 325 OAL 0500 Cut Diameter 05000 Shank Diameter

Niagara Cutter N35160 High Speed Steel Square Nose End Mill, Weldon Shank, TiN Finish, Roughing/Finishing Cut, Non-Center, 30-Degree, 4-Flute, 3.25″ OAL, 0.500″ Cut Diameter, 0.5000″ Shank Diameter

Niagara Cutter N35160 High Speed Steel Square Nose End Mill, Weldon Shank, TiN Finish, Roughing/Finishing Cut, Non-Center, 30-Degree, 4-Flute, 3.25″ OAL, 0.500″ Cut Diameter, 0.5000″ Shank Diameter - High-speed steel is compatible with a variety of materials. Center-cutting design allows the end mill to plunge into material like a drill bit while also performing conventional surface milling. Square nose end mills (also called square end) create sharp, unrounded cuts. Number of flutes varies fewer flutes have more chip-carrying capacity and more flutes produce a finer finish. Titanium nitride (tin) is a general-purpose coating that combines high-temperature resistance and increased hardness compared to uncoated end mills.

 

Niagara Cutter N46712 Cobalt Steel Square Nose End Mill Weldon Shank Uncoated Bright Finish Finishing Cut Non-Center 30-Degree 6-Flute 4 OAL 0844 Cut Diameter 0625 Shank Diameter

Niagara Cutter N46712 Cobalt Steel Square Nose End Mill, Weldon Shank, Uncoated Bright Finish, Finishing Cut, Non-Center, 30-Degree, 6-Flute, 4″ OAL, 0.844″ Cut Diameter, 0.625″ Shank Diameter

Niagara Cutter N46712 Cobalt Steel Square Nose End Mill, Weldon Shank, Uncoated Bright Finish, Finishing Cut, Non-Center, 30-Degree, 6-Flute, 4″ OAL, 0.844″ Cut Diameter, 0.625″ Shank Diameter - Cobalt steel resists abrasion and high cutting temperatures, and has higher feed rates than high-speed steel. Uncoated (bright) tools have no additional surface treatment or coating for use on a broad range of materials. Non-center-cutting design supports peripheral milling and finishing. Square nose end mills (also called square end) create sharp, unrounded cuts. Number of flutes varies fewer flutes have more chip-carrying capacity and more flutes produce a finer finish.

 

Moldings Online 3798978243 78x 1x 037 Armstrong Loft Gray Alterna Maple Mini Square Nose 78 L

Moldings Online 3798978243 78″x 1″x 0.37″ Armstrong Loft Gray Alterna Maple Mini Square Nose, 78″ L

Moldings Online 3798978243 78″x 1″x 0.37″ Armstrong Loft Gray Alterna Maple Mini Square Nose, 78″ L - Square nosing is ideal for concealing expansion spaces along a vertical object that cannot be framed, such as sliding glass door or brick fireplace. .

 

CGC Tools CEM18F4TIALN Primate Square Nose End Mill TiAlN Coating 4 Flute 18 Diameter 12 LOC 1-12 OAL

CGC Tools CEM18F4TIALN Primate Square Nose End Mill, TiAlN Coating, 4 Flute, 1/8″ Diameter, 1/2″ LOC, 1-1/2″ OAL

CGC Tools CEM18F4TIALN Primate Square Nose End Mill, TiAlN Coating, 4 Flute, 1/8″ Diameter, 1/2″ LOC, 1-1/2″ OAL - This weapon of mass production destroy any competition. Usa, flat, 4 flute, 1/8” diameter, 1/2” length of cut, 1-1/2” overall length, tialn coating. Highest transverse rupture strength (trs) nano-grain carbide substrate available and completely resharpenable. Extremely versatile in various materials, center cutting, solid sub-micron carbide. Gmp edge prepped to hone the “ridges” to reduce fracturing during the milling process while greatly increasing tool life and enhancing finish.